Updates Since 2023

Flybridge

• Helm station customized and updated
• New custom fitted helm station cover
• New cushion upholstery on flybridge seating
• New custom fitted cover for seating area
• New grill
• New custom sunbrella shade cover for over flybridge open area
• New removable tender chocks (flush mount, when removed reveals an open deck free of chock hardware.)
• New winch motor in davit (new spare winch motor stored in v birth storage)
• New dyneema davit lines and tender harness
• Flybridge rail modified for easier tender deployment/retrieval
• Custom black sunbrella skirting safety/privacy surrounding flybridge railing
• Custom sheath for isenglass enclosure
• New VHF late 2025
• Both VHF antennas replaced late 2025

Exterior

• Bow - New cushion upholstery
• Bow - New custom fitted seating/cushion cover
• All teak sanded, stained, several coats late 2025
• All windows/openings/hatches re caulked late 2025

Pilot house

• Extensive customization to helm station
• New Dometic HVAC early 2026
• New ice maker late 2025

Salon

• New Dometic HVAC early 2026
• New refrigerator early 2026
• New inductive stove top mid 2025
• New Splendid washer/dryer all in one unit 2025

Cabins

• 2 new Dometic HVAC 2024

General

• Waste hoses/lines vents replaced 2025
• Both engines serviced (Heads off inspected, valves speced, intercoolers inspected/cleaned, coolant flush/change, oil, etc 2026
• Updated music/speakers/amps cockpit, salon, master, flybridge
• New hot water heater 2025

Electric

• House batteries converted to lithium 2024
• Charger, inverter, solar charger, etc all converted to Victron when house batteries were upgraded to lithium
• High output alternator
• Start and bow thruster batteries new 2024/2025

Updates Done Between 2018 and 2023

• New upgraded five blade bow thruster propellers
• Two new Garmin 4" GMI20 Displays on fly bridge
• New Garmin VHF 210 radio on fly bridge
• New granite counters, sinks and faucets in bathrooms
• New Garmin 4" GMI20 display in pilot house
• Installed new 120 amp high output alternator on each engine
• New bus bars throughout engine room
• Installed new transom underwater lights
• New 400’ 3/8 galvanized anchor chain
• New Lebroc helm chair on fly bridge
• New Magnum gas grill
• Replaced fuel lines and water lines both engines
• New Magnum house bank inverter
• New barrier coat on bottom 2021 (done again in 2024)
• Installed 1200 watt solar panels and controller
• New generator battery New LED running lights
• New galvanized Rocna 121lb bow anchor
• New white leather sofa in salon
• Installed two new deck boxes on fore deck
• Two new Stressless electric leather recliners in salon
• New raw water pumps and spares for engines and generator
• New Seawater Pro 40 gal/hr water maker
• New Racor closed crankcase vent system on both engines
• 2018 New cutlass bearings Remove and balance shafts and props
• 10 New life jackets

Accommodations

The main salon features a leather couch to stb and two custom easy chairs to port creating a warm and inviting living space. The salon/galley area has custom roll down blinds. Aft, the covered deck offers an FRP hardtop and comfortable deck furniture for outdoor relaxation. The flybridge has access via the pilothouse and and aft deck ladder and includes an upper helm station, full electronics, and an FRP hardtop, with a spacious aft deck equipped with a davit crane for tender handling.

Below, the forward cabin offers two bunk‑style berths with hanging‑locker storage, adjacent to an enclosed head with a 12V toilet. A second separate guest stateroom provides two additional berths and ample locker space. The master stateroom features a centerline queen berth, generous storage, and a private head with a freshwater 12V toilet and separate shower stall.

The pilothouse includes a well‑equipped helm station, electronics suite, and electrical load panels, along with a fixed table and bench seating just aft.

The salon, galley, pilothouse includes

• Curtains on all salon windows
• Splendid 110v washer/ dryer combo
• Uline ice maker
• Intellivision Satellite TV System with Salon 43" Samsung LED TV, 32" Toshiba LED TV (in the master) & 19" Insignia LED TV (in a guest stateroom)

Galley

The spacious U‑shaped galley opens directly to the main salon, creating an ideal workspace for liveaboards, extended cruising, or relaxed weekend trips. A long stretch of countertop and a raised serving bar make meal prep and entertaining effortless. Abundant storage and full‑size appliances give the onboard chef everything needed to prepare gourmet meals with ease.

• New Summit stainless 110V commercial‑grade refrigerator/freezer
• Breville stainless 110V inverter/microwave oven
• New Z-Line 24in Induction Cooktop, 4 Burner, including installation and custom fabrication done in 2024
• New Hot water heater in 2025
• Replace Icemaker in pilothouse 2025
• Washer dryer combo is under the serving bar

Electronics

Interior Navigation

• All new Garmin Electronics in 2024 VHF in 2025
• Kobelt electronic engine controls
• Vesper Marine AIS Watchmate Transponder model MX850
• MOFI Networks 5G modem/router model MOFI5500-5GXeLTE
• YeoLink security system with remote monitoring
• Garmin In-Reach explorer+ satellite communicator
• Cobra handheld VHF model HH500
• Richie marine compass

Flybridge Navigation Electronics

• All new Garmin Electronics in 2024 VHF in 2025
• Naiad Stabilizer remote
• Garmin GHP20 autopilot controller
• Garmin 210 VHF radio

Entertainment

• Intellivision Satellite TV system:
• 43” Samsung LED TV
• 32” Toshiba LED TV
• 19” Insignia LED TV

Mid 2024 there was an extensive refit of the electronics and all the cosmetic panel housing electronics, engines, stabilizers were replaced.

Upper Helm:

·      Custom built fiberglass upper helm display with acrylic front with new wire chases under helm.

·      All wiring to and upper and lower helm electronics.

·      Tie up all wiring for hardtop and electronics.

·      Replace all lighting control switches and connectors at upper helm.

Lower Helm: 

·      Lower helm new acrylic panels. 

·      Install all accessories, switches and labels.

·      Create new acrylic template for lower helm stabilizer control.

Miscellaneous:

·      Install mast head camera and replace all engine room and lazarette cameras with Garmin GC14's.

·      Remove headliners in master strm and salon.

·      Fabricate and install speaker mounts in master, salon and lower helm.

·      Fabricate teak speaker bezels and varnish. Install bezels and speakers.

·      Replace stbd VHF antenna wiring from antenna to AIS, and AIS to VHF at lower helm.

·      Fabricate backing and install sides of lower helm.

·      Fabricate all trim for lower helm and install.

·       Port side helm horizontal surface install matte black laminate.

·      Replace outlets with dual USB outlets.

·      Fabricate new outlet standoffs from solid teak and varnish.

·      Mask and beauty-ring upper helm gauge and switch box.

New Electronics installed at this time were:

·      Garmin Reactor 40 Autopilot w/GHC50 Display Unused                

·      Axis P7304 Video Encoder                  

·      Garmin GHC50 Autopilot Dislplay                 

·      Garmin 9-Axis Autopilot Heading Sensor                  

·      Garmin J1939 Cable for GPSMAP 8600                      

·      Garmin GMS10 Network Port Expander                     

·      Garmin GC14 Marine Camera          

Additional Equipment and Electrical

• (4) Air conditioning units, Marine Air system (New 2025-2026)
• (2) 12v freshwater, electric Raritan marine heads (New between 2018-2023)
• (1) 110v 20 gallon hot water heater (New 2025)
• (2) Shurflo 12v pressure water pumps
• Maxwell 1800 anchor windlass
• Gulf Coast fuel polishing system
• Naiad 12v roll stabilizers
• Side Power bow thruster
• One 12v oil change pump
• Three windshield wipers
• Hynautic hydraulic steering system
• Three 380W solar panels
• Bower systems 800lb hydraulic crane
• Cablemaster shore power retraction system

Lithium Battery System installed in 2024:

·      4ea Victron 200Ah Superpacks

·      8D Bow Thruster Battery

·      1ea Zues Alternator Regulator

·      2- 500A Shunts for Regulator

·      1ea Victron Orion 50A DC-DC Charger

·      1ea Lifeline 8D AGM Battery

·      Victron Lynx Distributor

Extensive rewiring of the ship’s wiring systems was done in 2024/2025 including:

·      Replace Eng and Gen Battery Charger with Victron Smart IP43 12V 50A Charger

·      Install Victron system

·      Pull new ground wires.

·      Change inverter charger wiring @ AC panel –Install transfer switch & rewire

·      Find & separate all neutrals on the boat, pull new neutral to engine room

·      Replace stbd. alternator with Balmar 170A - run new 4/0 positive & negative cable from alternator buss, regulator wiring, wire & fusing

·      Smart battery protect

·      Digital multi control 200GX 1

·      MultiPlus 120V VE. Bus 1

·      Smartshunt 500A/50MV

·      Smart battery protect 12/24V 220A breaker 200A

·      SmartSolar MPPT 150/70

·      Victron Cerbo GX Communications hub

·      Victron GX touch 70 display

·      VE direct to USB interface

·      Phoenix Smart IP43 charger 50A

Engine room /Lazerette

Engine room access is via the aft lazarette or the floor in the galley. The aft lazarette is accessed via an aft deck hatch and has enormous storage capacity for all your extras and spares. There is a door into the engine room also from there.

Engine room is clean, tidy and has extensive updates done to it.

Extensive Mechanical work done recently:

• Service PRT & STB main engines,
• R&R lube oil filter, primary fuel filters,sec. fuel filters,
• R&R raw after impellers,
• Replace PRT raw water hose from pump to formed hard piping,
• Replace hardware bolt's on STB raw waterpump cover,
• Replace zincs PRT & STB transmission,
• Pull rocker covers PRT & STB main engine, check overhead int. exchange, adjust valve train,
• R&R raw water circuit zinc's scope, inspect cooler, flush cooling system after boat is splashed,
• Service gen-set, R&R lube oil filter, primary fuel Racor 500, sec. fuel filter, check coolant,

Recent Bottom Work

• Barrier coat before bottom job, with prop speed done in 2025. 
• Cutlass bearings props balanced etc beginning of 2026. 
• Rudder boxes serviced 2026.

Rudder work - started out replacing packing in glands, ended up doing all of the below while out of the water as preventative: 

• Drop and Repack Both Rudder Glands, Replace Cutlass Bearings in Rudder Housings
• Thrust Bearings for Rudders
• Part: New Mouning Hardware
• 2 Coat Bottom Job Trinidad HD - Black
• Replace Port and Starboard Rudder Post
• Custom Manufactured Aquamet 22 2-3/4" Rudder Post Machined with 3/4" Stainless Mounting Plate

Exclusions

Dingy and Motor are Excluded.

Personal Gear and any gear not mentioned here.

Preliminary Listing Full Specs and Gear to be done.

Disclaimer

The company offers the details of this vessel in good faith but cannot guarantee or warrant the accuracy of this information nor warrant the condition of the vessel. A buyer should instruct his agents, or his surveyors, to investigate such details as the buyer desires validated. This vessel is offered subject to prior sale, price change or withdrawal without notice.

Mechanical Disclaimer

Engine and generator hours are as of the date of the original listing and are a representation of what the listing broker is told by the owner and/or actual reading of the engine hour meters. The broker cannot guarantee the true hours. It is the responsibility of the purchaser and/or his agent to verify engine hours, warranties implied or otherwise and major overhauls as well as all other representations noted on the listing brochure.